Which of the following specification will allow you to： associate VLAN groups to STP instances so you can provide multiple forwarding paths for data traffic and enable load balancing？ （）
A. IEEE 802.1d （STP）
B. IEEE 802.1s （MST）
C. IEEE 802.1Q （CST）
D. IEEE 802.1w （RSTP）
您可能感興趣的試卷
你可能感興趣的試題
Which of the following specifications is a companion to the IEEE 802.1w Rapid Spanning Tree Protocol （RSTP） algorithm， and warrants the use multiple spanning-trees？ （）
A. IEEE 802.1s （MST）
B. IEEE 802.1Q （CST）
C. Cisco PVST+
D. IEEE 802.1d （STP）
E. None of the other alternatives apply
pany uses MSTP within their switched LAN.
What is the main purpose of Multiple Instance Spanning Tree Protocol （MSTP）？（）
A. To enhance Spanning Tree troubleshooting on multilayer switches
B. To reduce the total number of spanning tree instances necessary for a particular topology
C. To provide faster convergence when topology changes occur in a switched network
D. To provide protection for STP when a link is unidirectional and BPDUs are being sent but not received
E. None of the other alternatives apply
The Company network utilizes the Multiple-instance Spanning Tree protocol in its switched LAN.
Which three statements about the MST protocol （IEEE 802.1S） are true？ （）
A. To verify the MST configuration， the show pending command can be used in MST configuration mode.
B. When RSTP and MSTP are configured； UplinkFast and BackboneFast must also be enabled.
C. All switches in the same MST region must have the same VLAN-to-instance mapping， but different configuration revision numbers.
D. All switches in an MST region， except distribution layer switches， should have their priority lowered from the default value 32768.
E. An MST region is a group of MST switches that appear as a single virtual bridge to adjacent CST and MST regions.
F. Enabling MST with the "spanning-tree modemst" global configuration command also enables RSTP.
On switch R1 you issue the "udld enable" global command.
What does this command accomplish？ （）
A. Enables all fiber-optic LAN ports for Unidirectional LINK Detection （UDLD）
B. Enables all copper media LAN ports Unidirectional Link Detection （UDLD）
C. Overrides the default UDLS setting for all ports
D. Globally enables all ports on the device for Unidirectional Link Detection （UDLS）
E. None of the other alternatives apply
Switch R1 has been configured with the root guard feature.
What statement is true if the spanning tree enhancement Root Guard is enabled？ （）
A. If BPDUs are not received on a non-designated port， the port is moved into the STP loop- inconsistent blocked state
B. IF BPDUs are received on a PortFast enabled port， the port is disabled.
C. If superior BPDUs are received on a designated port， the interface is placed into the root- inconsistent blocked state.
D. If inferior BPDUs are received on a root port， all blocked ports become alternate paths to the root bride.
最新試題
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
What two things will occur when an edge port receives a BPDU？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Which statement is correct about RSTP port roles？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）