Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Cisco 642-832： Practice Exam
Figure 2
Trouble Ticket Statement
Client 1 is able to ping 209.65.200.226 but not the Web Server at 209.65.200.241. Initial troubleshootingshows and R1 does not have any BGP routes. R1 also does not show any active BGP neighbor
Configuration on R1
CertKiller.com
router bgp 65001
no synchronization
bgp log-neighbor-changes
network 209.65.200.224 mask 255.255.255.252
neighbor 209.56.200.226 remote-as 65002
no auto-summary
On which device is the fault condition located？（）
A.R1
B.DSW1
C.R4
D.R2
您可能感興趣的試卷
你可能感興趣的試題
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Cisco 642-832： Practice Exam
Figure 2
Trouble Ticket Statement
HSRP has been configurationured between DSW1 and DSW2. DSW1 is configurationured to be activerouter but it never becomes active even though the HSRP communication between DSW1 and DSW2 isworking.
Configuration on DSW1
CertKiller.com
track 1 ip route 10.1.21.128 255.255.0.0 metric threshold threshold metric up 1 down 2!
track 10 ip route 10.2.21.128 255.255.255.0 metric threshold threshold metric up 63 down 64!
interface Vlan10
ip address 10.2.1.1 255.255.255.0
standby 10 ip 10.2.1.254
standby 10 priority 200
standby 10 preempt
standby 10 track 1 decrement 60
Configuration on R4
Cisco 642-832： Practice Exam
interface loopback0
ip address 10.2.21.128 255.255.255.0
What is the solution of fault condition？（）
A.Change standby priority to 140
B.Change standby priority to 260
C.Change standby 10 track 1 decrement 60 to standby 10 track 10 decrement 60
D.Change standby 10 track 1 decrement 60 to standby 10 track 1 decrement 100
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Cisco 642-832： Practice Exam
Figure 2
Trouble Ticket Statement：
Client 1 is able to ping 10.1.1.2 but not 10.1.1.1. Initial troubleshooting shows that R1 does not have anyOSPF neighbors or any OSPF routes
Configuration on R1：
router ospf 1
CertKiller.com
log-adjacency-changes
network 10.1.1.0 0.0.0.3 area 12
default-information originate always!
interfaceSerial0/0/0/0.12 point-to-point
ip address 10.1.1.1 255.255.255.252
ip nat inside
ip ospf message-digest-key 1 md5 TSHOOT
Configuration on R2：
router ospf 1
log-adjacency-changes
network 10.1.1.0 0.0.0.3 area 12!
Cisco 642-832： Practice Exam
interfaceSerial0/0/0/0.12 point-to-point
ip address 10.1.1.2 255.255.255.252
ip ospf authentication message-digest
ip ospf message-digest-key 1 md5 TSHOOT
What is the solution of the fault condition？（）
A.ipospf authentication message-digestcommand has to be added on S0/0/0/0.12
B.ipospf authentication message-digestcommand has to be added under the OSPF routing process
C.A static route to 10.1.1.4 must be added on R1
D.ipnat outside must be added on S0/0/0/0.12
最新試題
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
Drag and drop the xDSL type on the above to the appropriate xDSL description on the below.
Drag and drop question. The upper gives the MPLS functions， the bottom describes the planes.Drag the above items to the proper location at the below
As a network engineer， study the exhibit carefully. Router Net is unable to establish an ADSLconnection with its provider. Which action would correct this problem？（）
In computer security， AAA stands for authentication， authorization and accounting. Which optionabout the AAA authentication enable default group radius enable command is correct？（）
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define？（）
Drag the IOS commands from the left that would be used to implement a GRE tunnel using the10.1.1.0.30 network on interface serial 0/0 to the correct target area on the right.
IPSec VPN is a widely-acknowledged solution for enterprise network. Which three IPsec VPNstatements are true？（）
Drag and drop the steps in the process for provisioning a cable modem to connect to a headendon the above to the below in the order defined by the DOCSIS standard.