A.Action Management
B.Fault Management
C.Configuration Management
D.Protocol Management
E.Security Management
您可能感興趣的試卷
你可能感興趣的試題
Drag the DSL technologies on the left to their maximum（down/up） data rate values on the below.
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN？（）
A.A
B.B
C.C
D.D
A new router was configured with the following commands：
The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
A.To prevent customers from running TDP with the ISP routers
B.To prevent customers from running LDP with the ISP routers
C.To prevent other ISPs from running LDP with the ISP routers
D.To prevent man-in-the-middle attacks
E.To use CBAC to shut down Distributed Denial of Service attacks
F.To use IPS to protect against session-replay attacks
G.None of the above
A.PPPoE with the 827 configured as a bridge
B.PPPoE with the 827 configured as the PPPoE client
C.PPPoA
D.RFC 1483 Bridged with the 827 configured as the PPPoE client
E.RFC 1482 Bridged with the 827 configured as a bridge
A.Disable post scan
B.Use SSH or SSL
C.Enable trust levels
D.Deny echo replies on all edge routers
Network Topology Exhibit：
Configuration Exhibit：
NET（config）# access-list 112 deny icmp any any echo log
NET（config）# access-list 112 deny imp any any redirect log
NET（config）# access-list 112 deny icmp any any mask-request log
NET（config）# access-list 112 permit icmp any 10.1.1.0 0.0.0.255
NET（config）# interface Fa0/1
NET（config-if）# ip access-group 112 in
You work as a network administrator at networkTut.com， study the exhibit carefully. The
configuration has been applied to router NET to mitigate the threat of certain types of ICMPbasedattacks while allowing some ICMP traffic to the corporate LAN to work. However， the configurationis incorrect. On the basis of the information in the exhibit， which configuration option wouldcorrectly configure router NET？（）
A.The first three statements of ACL 112 should have permitted the ICMP traffic and the laststatement should deny the identified traffic
B.The last statement of ACL 112 should have been "access-list 112deny icmp any 10.2.1.00.0.0.255"
C.The last statement of ACL 112 should have been "access-list 112permit icmp any 10.2.1.00.0.0.255"
D.ACL 112 should have been applied to interface Fa0/0 in an inbound direction
E.The last statement of ACL 112 should have been "access-list 112deny icmp any 10.1.1.00.0.0.255"
F.ACL 112 should have been applied to interface Fa0/1 in an outbound direction
G.None of the above
A.The IP inspection rule can be applied in the inbound direction on the secured interface
B.The IP inspection rule can be applied in the outbound direction on the unsecured interface
C.The ACL applied in the inbound direction on the unsecured interface should be an extendedACL.
D.For temporary openings to be created dynamically by Cisco IOS Firewall， the access-list for thereturning traffic must be a standard ACL
最新試題
In computer security， AAA stands for authentication， authorization and accounting. Which optionabout the AAA authentication enable default group radius enable command is correct？（）
Drag the correct statements about MPLS-based VPN on the left to the boxes on the right.（Not allstatements will be used）
IPSec VPN is a widely-acknowledged solution for enterprise network. Which three IPsec VPNstatements are true？（）
cisco ios command to interface dialer 0
Study the exhibit carefully.Routers A and B are customer routers. Routers 1， 2， 3 and 4 are provider routers. The routers areoperating with various IOS versions. Which frame mode MPLS configuration statement is true？（）
As a network engineer， do you know for what purpose SDM uses Security Device Event Exchange（SDEE）？（）
Match the xDSL type on the above to the most appropriate implementation on the below.
Which three statements accurately describe IOS Firewall configurations？（）
Drag and drop each function on the above to the hybrid fiber-coaxial architecture component that itdescribes on the below.
Drag the DSL technologies on the left to their maximum（down/up） data rate values on the below.