A. admin， operator， network-admin， and network-operator
B. admin， read-only， network-admin， and network-operator
C. vdc-admin， vdc-operator， network-admin， and network-operator
D. vdc-admin， vdc-operator， network-admin， and network-operator （for Nexus 7000） and network- admin and network-operator （for other Nexus switches）
E. admin and read-only
您可能感興趣的試卷
你可能感興趣的試題
A. IGMP is not synchronized between vPC peers
B. Cisco Fabric Service carries IGMP entries across the vPC peer link
C. IP ARP synchronization under the vPC domain configuration also synchronizes IGMP
D. IGMP is flooded to the L2 domain， and there is no need to synchronize it between vPC peers
A. The OTV control-plane protocol uses the IS-IS protocol to establish adjacencies and exchange MAC reachability across the overlay network. You must enable IS-IS with the feature isis command before OTV adjacencies can be established.
B. OTV uses an SSM group range for neighbor discovery and to exchange MAC reachability with other OTV edge peers.
C. The OTV join interface is a routed uplink interface on the edge device used to physically join the overlay network.
D. The OTV internal interface encapsulates the site Layer 2 frames in IP unicast or multicast packets that are then sent to the other sites.
A. C84C·75FA·6000
B. 01005·E11.·2FD
C. C84C·76FA·6000
D. 4000.0000.0001
A.The following XML-based NETCONF operations are supported in NX-OS SoftwarE˙close-session copy-config delete-config and edit-config
B.The following XML-based NETCONF operations are supported in NX-OS SoftwarE˙close-session copy-config edit-config and kill-session
C.NX-OS Software supports up to a maximum of 16 concurrent XML sessions
D.Only show commands are supported via the XML management interface in NX-OS Software
E.The NX-OS implementation of the XML-based NETCONF requires SSH to be used for communication with the device
A. In a vPC topology， the primary HSRP router will respond to ARP requests， but both HSRP routers will forward data traffic. No additional configuration is required.
B. In a vPC topology， the primary HSRP router will respond to ARP requests， but both HSRP routers will forward data traffic if the peer-gateway feature is enabled.
C. You can configure two overlapping HSRP groups to load share traffic from the connected hosts while providing the default router redundancy.
D. You can use the show standby command to verify HSRP operation and configuration.
E. If you remove the feature hsrp command， all relevant HSRP configuration information isalso removed.
最新試題
On a Cisco Unified Computing System （UCS）， which two statements regarding Ethanalyzer are true？（）
Which are valid statements about Cisco Virtual Interface Card （VIC）？ （）
Application Control Engine （ACE） can check the health of servers and server farms by configuring health probes （which are sometimes referred to as keepalives）. A probe can be one of many types. Which are valid ACE probes？ （）
What is the use of an "all configuration" backup in Cisco UCS？（）
Refer to the exhibit.The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B （Path C）. Which actions might be used to change this behavior？（）
Which of the following are supported in Cisco Global Site Selector？ （）
What would be the cause for the following fault in UCS Manager？（） "ether VIF x / xxx down， reason： ENM source pinning failed"
In the event of a GSS failure in a GSS cluster， which is true？（）
Given the following output： san-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24：0c：00：0d：ec：d3：5c：00 Admin port mode is NP， trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member[1] ： fc2/3 Member[2] ： fc2/4 What does "Speed is 8 Gbps" indicate？（）
Which statement is true about "full state backup" in a Cisco Unified Computing System？（）