A. Because the configuration revision of the new switches is lower than the rest of the network，it can change the VLAN database of the other switches.
B. As a VTP server， the new switch deleted all VLANs of the network.
C. Erasing VLANs increases the VTP configuration revision.
D. Since the configuration revision of the network is higher than the new switch，the VLAN database was automatically synchronized.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Users from the Engineering VLAN complain that every time Business VLAN users have a network connectivity issue， the Engineering VLAN users usually have problems experiencing slow response or network connectivity problems. After troubleshooting， an unauthorized switch 2 was found. This unauthorized switch has been a regular problem， assuming the root bridge function under the spanning-tree domain and causing the
Engineering VLAN to be unstable. Which three of these actions could be suggested to fix the problem？（）
A. Upgrade Spanning Tree Protocol to Rapid Spanning Tree Protocol.
B. Change Business VLAN PCs to switch 1 and switch 4.
C. Force the root bridge to be switch 2， instead.
D. Adjust spanning-tree timers （max-age and forward-delay）.
E. Shut down all unused ports.
F. Use MSTP to separate the Engineering VLAN from the Business VLAN to optimize spanning-tree convergence time within each VLAN
A.Binding should be manually configured.
B.It is not supported if IEEE 802.1x port-based authentication is enabled.
C.The DHCP server must support option 82， or the client is not assigned an IP address.
D.It filters based on source IP address only.
Refer to exhibits 1 and 2. In exhibit 1， all users on the LAN segment use router A as the active HSRP router. Router B is the standby router for the HSRP. In exhibit 2， the network management team reported that there is no utilization on the WAN link B. To solve this problem， you decide to change the logical topology of your LAN， but you are not sure about what changes must be made. You must manage HSRP or change it to another protocol in order to provide the most scalable design， automatic redundancy， and load balancing. Which one of these actions would be the best choice？ （）
A. Use MHSRP， with three users using router A as the default gateway and three users using router B as the default gateway.
B. Keep HSRP and activate PBR to redirect half of the traffic to the other WAN link.
C. Use the backup interface on the WAN link B to provide load balancing for all users.
D. Use GLBP instead， because it provides you with up to three MAC addresses for the same default gateway virtual IP address.
E. Use GLBP instead， because it provides you with up to four MAC addresses for the same default gateway virtual IP address.
A.SMTP
B.ICMP
C.BGP
D.SSH
E.RTP
F.BitTorrent
G.VTP
Refer to the exhibit. The Layer 2 network uses VTP to manage its VLAN database. A network designer created all VLANs on the VTP server （switch 1） and it has been advertised through VTP to all other VTP clients （switches 2 through 4）. Due to network growth， a network operator decided to add a new switch between switch 1 and switch 3. The network operator has been instructed to use a refurbished switch and use a VTP client. Which three of these factors should the network operator consider to minimize the impact of adding a new switch？（）
A. Pay special attention to the VTP revision number， because the higher value takes the priority.
B. Configure all VLANs manually on the new switch in order to avoid connectivity issues.
C. A trunk should be established between the new switch and switches 1 and 3 as VTP only runs over trunk links.
D. Set at least the VTP domain name and password to get the new switch synchronized.
E. An ISL trunk should be established between the new switch and switches 1 and 3， because VTP only runs over ISL.
F. Pay special attention to the VTP revision number， because the lower value takes the priority.
最新試題
Which three message types are valid PIMv2 message types？（）
When STP UplinkFast is enabled on a switch utilizing the default bridge priority， what will the new bridgepriority be changed to？（）
Which command is used to enable SSM with the range 232.0.0.0 - 255.0.0.0？（）
What is also called Type 0 authentication in OSPF on Cisco Routers？（）
Choose two commands that are required to enable multicast on a router， when it is known that thereceivers use a specific functionality of IGMPv3.（）
Which two statements about SA caching are true？（）
An expanding company is deploying leased lines between its main site and two remote sites. Thebandwidth of the leased lines is 128kb/s each，terminated on different serial interfaces on the main router.These links are used for combined VOIP and data traffic. The network administrator has implemented a VOIP solution to reduce costs，and has therefore reserved sufficient bandwidth in a low latency queue oneach interface for the VOIP traffic. Users now complain about bad voice quality although no drops areobserved in the low latency queue. What action will likely fix this problem？（）
What is true about Unicast RPF in strict mode？（）
In Layer 2 topologies， spanning-tree failures can cause loops in the network. These unblocked loops cancause network failures because of excessive traffic. Which two Catalyst 6500 features can be used to limitexcessive traffic during spanning-tree loop conditions？（）
What is the command to configure RSVP to reserve up to one-tenth of a Gigabit link，but only allow eachindividual flow to use 1 MB/s？（）